Save on Pinterest

8 Clever Tool Hacks

Here's a great collection of tool hacks for every level of DIYer, from beginner to advanced. These simple tips and techniques will help you get the most out of your tools.

1 / 8
Hang your roofing toolsFamily Handyman

Hang Your Roofing Tools

Use spring clamps to keep your hoses, extension cords, and other tools and materials from sliding off the roof.

Don’t try this on brittle or scorching hot shingles or you may damage them. You can create a handier hook by sticking the clamp in a vise and bending up one of the handles.

2 / 8

Clamp With a Tie-Down Strap

If you need to clamp boxes together, a ratchet tie-down strap can often do the job just as well as band clamps.

Just make sure to protect the wood under the ratchet and hooks with cardboard. This troubleshooter will help with your truck tie-down problems.

3 / 8
Mix concrete with a rakeFamily Handyman

Mix Concrete With a Rake

Try a garden rake instead of a hoe the next time you have to mix concrete. The rake won’t splash as much water over the edge, and the tines do a good job of combining the water with the powder. With a hoe, you waste a lot of time just pushing powder around the tub.

Also, here’s how to finish concrete properly.

4 / 8
Make mini roller coversFamily Handyman

Make Mini Rollers

Next time you’re in the paint department, pick up a 3-in. roller frame, the type that takes the same diameter cover as a standard 9-in. roller. You can then cut any 9-in. roller cover into three 3-in. covers to fit it.

A 3-in. roller is perfect for painting trim or small stuff like a mailbox, but not every store carries 3-in. covers. This little trick will also cut the cost of the 3-in. roller covers in half.

Mark the 9-in. roller covers 3 in. in from each end. Cut into equal pieces with a hacksaw, holding the cover steady with a bar clamp. Trim the rough edges of the nap with scissors.

5 / 8
Use a level to Extend your table saw fenceFamily Handyman

Use a Level To Extend Your Table Saw Fence

The only way to achieve a perfectly straight cut is to keep your material tight up against the table saw fence. But that’s hard to do when you’re cutting a large sheet of plywood on your own.

Extending the fence with a 4-ft. level will make it easier to keep the plywood on a straight and narrow path as it approaches and passes through the blade. Hold the level in place with a couple clamps. Here are some more table saw tips.

6 / 8
Need a hole in hard soil? Use a Drill!Family Handyman

Need a Hole in Hard Soil? Use a Drill.

Have you ever waited too long to install your reflective driveway markers and discovered the ground was frozen? Or tried to install a yard sale sign in dry soil that’s as hard as concrete? Well, why not treat it as if it really were concrete and drill holes into it with a masonry bit?

7 / 8
Make a blade for cutting foamFamily Handyman

Make a Blade for Cutting Foam

A jigsaw will cut through rigid foam like butter—except butter doesn’t crumble into thousands of bits that mess up your shop, basement or garage. If you remove the teeth from a jigsaw blade, it will cut the foam just as well but without the mess.

Remove the teeth with a grinder, and be sure to wear eye protection. Hold on to the blade with locking pliers, not your fingers. Here is a simple DIY sandpaper cutting jig, too.

8 / 8
Lift heavy stuff with a flat pry barFamily Handyman

Lift Heavy Stuff With a Flat Pry Bar

If you’ve ever had to remove a solid-core door, you know how heavy they can be. Lifting them up to reinstall hinge pins can be a challenge if you’re working alone, but a flat pry bar (aka “flat bar”) can give you just the leverage you need.

If your flat bar won’t raise the door high enough, install a small block of wood at the fulcrum point of the pry bar to increase the lifting distance. Hold the block in place with a small screw and washer.

Make sure the screw doesn’t poke through. If it does, grind off the end so it won’t damage the floor. This same setup can be used to raise bottom drywall sheets off the floor for fastening.

Newsletter Unit

CMU Unit

Subscribe & SAVE 1 Year Subscription
for only $10!