How to Clean and Unclog a Kitchen Sink Drain

With two simple tools — a plunger and a drain snake — you can clear 95 percent of your stopped-up drain problems.

Our editors and experts handpick every product we feature. We may earn a commission from your purchases.

Next Project

An hour or less




Less than $20


Save yourself the plumbing service call and unclog your drain yourself. In this article, we'll show you how to unclog a kitchen sink using a plunger and drain snake to clear up the most stubborn drain clogs.

Tools Required

  • Allen wrench
  • Clamps
  • Pipe wrench
  • Pliers
  • Plunger

Materials Required

  • Baking soda
  • White vinegar

Project step-by-step (9)

Step 1
Don’t plunge or snake a drain if you’ve poured drain cleaners into the sink. The chemicals can cause serious burns if they splash on your skin. Use drain cleaners only if the sink is draining slowly and not completely clogged.

Start With the Right Tools

  • Plungers are sold at any hardware store or home center.
    • Pro tip: Those with larger rubber bells deliver more thrust, but most sizes will work for kitchen drains. Be sure the plunger has a stout handle so you can apply plenty of force as you learn how to unclog a sink.
  • A drain snake (sometimes called a hand auger) is a long, serpentine tool which, as the name suggests, snakes into the drain and penetrates and pulls out the clog.
    • Drain snakes vary greatly in price, depending on their size, length and turning mechanism. For all-around use, the best drain snake is a 3/8-inch model that’s about 20 feet long. It’s easy to turn down into the drain. Shorter, 1/4-inch types will work for most clogs, too.
    • Pro tip: Since unclogging stubborn drains hopefully won’t be a regular activity in your home, consider renting a high-quality drain snake over buying a cheap one.
  • Keep these other items handy:
Step 2

Check the Garbage Disposer First

  • If the side of the sink that has the disposer doesn’t drain, plunge it first to remove the clog or force it down the drain.
    • Note: One of the most common causes of a clogged drain is when your garbage disposer is clogged.
  • If you flip the switch to turn on your garbage disposer and all you hear is a low humming sound, your disposer is probably jammed. Switch it off and unplug the unit.
  • You can usually free it by turning the blades manually by inserting an Allen wrench into the hole on the bottom of the disposer.
  • If the disposer doesn’t make any sound when you turn it back on, an internal breaker on the motor has probably tripped. Give the disposer a minute to cool off. Then press the reset button located on the bottom of the unit, and turn it on again.

clogged drain garbage disposal Family Handyman

Step 3

Clamp Off the Dishwasher

  • If you have a dishwasher, tighten a clamp over the flexible part of the drain line before plunging the drain.
    • Note: This prevents dirty water from flowing back into the dishwasher cabinet.

garbage disposal clogged drainFamily Handyman

Step 4

Get Busy With the Plunger

  • If the problem isn’t in the disposer, plunge the drain.
  • Fill the sink with 3 to 4 inches of water to ensure that the plunger seals around the drain.
    • Pro tip: Hold a wet rag tightly over the other drain opening in double sinks or use the basket strainer to seal it.

clogged sink plungerFamily Handyman

Work the Plunger

  • Plunge up and down vigorously for about 20 seconds.
    • Pro tip: Roll the head of the plunger into the water so you force water, not air, into the drain.

clogged sink plungerFamily Handyman

Pop the Plunger

  • On your last upstroke, pop the plunger off the mouth of the drain for extra pressure. If the water doesn’t swirl straight down the drain, continue plunging for several minutes. Learn how to clean a copper sink.
    • Pro tip: Plunging can be quick and easy or it can be a wet mess. Keep towels handy to soak up spills.
Step 5

Clean the P-Trap

  • If intensive plunging doesn’t remove it, disassemble and clean out the P-trap.
    • Note: Clogs that occur in the P-trap and trap arm of the drain most often occur when grease or coffee grounds build up. 

Disassemble the Trap

  • Loosen the slip nut on the trap arm assembly and the continuous waste tee and wiggle the trap free.
    • Pro tip: Begin by sponging the water from the sink to reduce the flow under the sink when you pull off the trap. Keep your pan or bucket underneath; dirty water will flow out. 
      • Note: We show plastic drain lines, but many older kitchen sinks have metal traps and pipes. Metal slip nuts are usually more difficult to loosen than plastic, but either will probably require the use of slip-joint pliers to break them free. Loosen them gently to avoid cracking or bending the trap assembly.

clogged sink drainsFamily Handyman

Step 6

Clean Out the Trap

  • Unscrew the slip nut between the P-trap and the trap arm first, then the nut at the bottom of the waste tee.
  • Clean out any debris from the P-trap.
    • Pro tip: Inspect both the P-trap and the trap arm for cracks or weak walls. If it’s worn, replace it to avoid problems in the future.
  • Reinstall the P-trap and test the line with warm water.
    • Pro tip: Don’t over-tighten the slip nuts. Hand-tight plus a quarter-turn with pliers should be enough.

clogged sink gunkFamily Handyman

Step 7

Remove the Trap Arm

  • If the P-trap isn’t clogged, move on and remove the trap arm and clean it.
  • To remove the trap arm, loosen the slip nut and slide the trap arm from the drain line stub-out.
    • Pro tip: You will likely need pliers to remove the nut.
  • Next, run a screwdriver around the inside of the pipe stub-out and pull out any debris that may have collected in the opening.
  • If you still haven’t found the clog, reach for the snake!

clogged sink drainFamily Handyman

Step 8

Insert the Drain Snake

  • Loosen the setscrew at the tip of the snake and pulling out 6 to 10 in. of cable.
  • Then tighten the setscrew and spin the drain snake down into the drain line.
    • Pro tip: Initially, you may feel an obstruction, but it’s likely that the tip of the snake is just turning a corner. Loosen the setscrew, pull out another 6 to 10 in. of cable and continue to feed the snake into the line.
  • Thread the tip of the drain snake into the drain stub-out. Tighten the setscrew and turn the crank clockwise to feed it into the drainpipe.

clogged sink drain snake the lineFamily Handyman

Turn the Drain Snake Through the Clog

  • Continue to turn the snake when you encounter resistance.
    • Note: The snake tip is designed to corkscrew through clogs and around corners.

snake drain cloggedFamily Handyman

Retract the Drain Snake

  • When you feel the cable hit an obstruction, continue cranking and pushing the cable through the clog until you feel the tip bite through.
    • Note: This should be obvious because the tension in the cable will drop.
  • When you are through the clog, turn the crank counterclockwise and pull out the cable.
    • Pro tip: Clean the cable as you pull; it’ll probably be covered with incredibly dirty gunk. You may get a large plug of material at the end of the snake, so keep that bucket handy.
  • Repeat the process until you no longer feel a blockage, then reassemble the trap and run plenty of warm water to flush the line.

remove the snake clogged drain gunkFamily Handyman

Step 9

Clean the Drain

  • After the drain is open, pour 1/2 cup of baking soda and 1/2 cup of white vinegar into the drain. Cover both openings and let it sit for a few minutes.
  • Then run another gallon or so of warm water behind it to flush out the mixture.
    • Note: The combination of baking soda and vinegar will break down any leftover fat deposits and will leave your drain smelling fresh.
  • Reinstall the P-trap and run water to test the drain.